The short answer
Most tile problems do not come from the tile but from the surface beneath it and how it is bonded. Laying on an uneven or damp base, too little adhesive behind the tile, and missing expansion joints are among the most common causes of cracking, hollow spots and lifting. Ask about preparation before you ask about tile type.
Preparation mistakes
- Tiling over an uneven floor or one with dust and oil.
- Not treating cracks and damp before installation.
- No waterproofing under bathroom and kitchen tiles, or no flood test.
- No falls toward drains, leaving standing water.
Bonding and installation mistakes
- Using an adhesive unsuited to the tile type, size or location.
- Spotting adhesive instead of covering the back of the tile, creating hollow areas that crack underfoot.
- Not pressing and levelling each tile.
- No expansion joints at walls and in large areas.
- Walking on tiles or grouting before the adhesive has cured.
Signs of a problem
- A hollow sound when tapped.
- A crack running along one line across several tiles.
- Raised or lifting tile edges, especially in summer.
- Damp or salt staining at the joints.
- Discoloured or crumbling grout.
Questions to ask the contractor
- How do you check floor level before laying?
- Is the waterproofing flood-tested before tiling?
- Which adhesive will you use and why?
- How do you plan the layout and expansion joints?
- How long before grouting and walking on the floor?
Why these problems show up more in the Eastern Province
Several conditions make tiling flaws clearer here: high summer heat dries adhesive quickly and expands tile, humidity near the coast enters floors in contact with the ground, and salts crystallise behind tile and push it off. Average workmanship that might pass in a mild climate can show its flaws quickly here. A good contractor accounts for these conditions when choosing adhesive, sequencing work and protecting the floor after laying.
How to find hollow spots before you accept the floor
Ask for a tap test before handover. Tap each tile with the edge of a light tool; a solid sound means good bonding, a hollow sound means a void beneath. A few small voids at the edges can be acceptable on some tile types, but many voids, or voids in the middle of large tiles, need fixing before handover because they will crack in use. Photograph the problem and send it before the work is closed and the final payment is made.
Checking level and edges
Lay a long straightedge on the floor in several directions and watch for gaps beneath it. Also run your hand across tile joints; a raised edge (lippage) shows in side lighting and catches feet. Large, glossy formats show this flaw most, so they need precise levelling systems. Check falls in bathrooms and outdoor areas by pouring a little water and watching whether it runs toward the drain.
Local repair or relay the floor?
If a few scattered tiles are hollow or broken, they can often be replaced locally provided spare tiles from the same batch exist. If the problem is general, such as an uneven floor, rising moisture or no expansion joints, local repair patches the symptoms and the defect returns. In that case the answer is to remove the affected area, treat the cause and relay. That is why we inspect before promising a repair and explain your options clearly.
A simple document that protects you: the method statement
Ask the contractor to write down what will be done: adhesive type and specification, preparation method, waterproofing and flood-testing in bathrooms and kitchens, expansion joints, grout type, and the wait before walking on the floor. It does not need to be complicated; one clear page is enough. It makes the conversation about quality objective and reduces disputes at handover because both sides know what was agreed.
Mistakes at thresholds, doors and corners
Many defects appear not in the middle of the room but where surfaces meet. Agree the finished floor level before tiling, because new tile plus adhesive raises the floor and can stop doors opening or leave a small step between rooms.
- Set the finished floor level before starting and check its effect on doors, thresholds and the tiles of adjoining rooms.
- Use a suitable transition strip or threshold between two tile types instead of leaving an exposed edge that chips.
- Use flexible silicone, not cement grout, where the floor meets the wall and in bathroom corners, because these joints move.
- Do not bury existing movement joints in the concrete under the tiles without a matching joint in the tiling.
What to do if you spot a mistake during the work
Stop work on the affected area and ask for it to be checked before more tiles go on or the joints are grouted. Write the note, attach a photo and send it to the contractor the same day. Lifting a few tiles after one day is far easier than lifting a whole room once the adhesive has set, and a written agreement on the fix protects both sides.
Ask for an inspection before tiling
Send photos of the space and room sizes on WhatsApp, and we will check the floor and waterproofing and propose the right approach before tiling starts.
Related services: Tiles, Marble & Granite, Waterproofing & Insulation, Villa Finishing & Interior Works
This service in your city: Dammam, Al Khobar, Dhahran, Qatif, Jubail, Al Ahsa (Hofuf)
Frequently asked questions
What is the most common reason tiles crack after installation?
The most common cause is a void under the tile from too little adhesive or adhesive applied in dabs, followed by an uneven base and missing movement joints. A tile fully bedded on a flat base rarely cracks under normal use.
Does a hollow-sounding tile always need replacing?
Not always. A small void at the edge of a tile can last for years without trouble, but many hollow spots or voids in the middle of large tiles mean poor bond and need checking, usually replacement, before they crack.
When can I walk on new tiles?
Once the adhesive has set according to its manufacturer's instructions, which vary with the product, heat and humidity. Ask the contractor for the time printed on the adhesive bag used and do not allow walking or moving furniture before then.
Does summer heat affect tile installation?
Yes. High heat dries adhesive before it bonds well to the tile, so work is better done at cooler times and in shade, mixing small batches of adhesive at a time.
Related guides
- Installing Large-Format Porcelain: Levelling and Adhesive
- Tiling in Summer Heat: Adhesive and Curing
- Tile Grout and Joints: Choice, Filling and Leak Prevention
- Preparing an Old Floor Before Laying New Tile