The short answer
Pools and tanks need waterproofing designed for permanent immersion, which differs from roof waterproofing exposed to rain. It is applied after preparing the concrete and treating cracks and joints, and tested by filling with water and watching the level; drinking-water tanks need materials suitable for contact with drinking water.
Why pools and tanks lose water
- Hairline cracks or untreated construction joints.
- A system not suited to constant water pressure.
- Leaks around suction and drain pipes.
- Ground movement or settlement near the foundation.
- Membrane damage from chlorine or salts.
The correct steps
- Inspect the concrete, repair cracks and clean and prepare the surface.
- Detail corners, joints and areas around pipes.
- Apply the suitable system in layers as specified.
- Fill-test and watch the level for several days before finishing.
- Tile or finish with an adhesive suited to immersion and proper joints.
Drinking-water tanks
Waterproofing materials used inside a drinking-water tank must be suitable for contact with drinking water, and the tank must be washed and disinfected before use. Ask the contractor for the material type and manufacturer before agreeing.
Signs you need an inspection
- Water level dropping without an obvious reason.
- Damp or staining around the tank or pool.
- Peeling membrane or tiles inside.
- Algae growth or salt deposits at joints.
Underground tanks: pressure from inside and outside
An underground tank takes water pressure from the inside when full, and soil moisture or groundwater from the outside when its level drops. Near the coast, where groundwater can sit close to the surface, the outside pressure matters, and salty water can seep into the tank instead of water leaking out. So:
- In a new build, the tank is waterproofed on the outside before backfilling, because the outer wall is hard and costly to reach later.
- An existing tank is treated from the inside with a system suited to negative (back) pressure and to contact with drinking water, after repairing cracks and joints.
- The tank opening and cover are sealed so wash water or rain cannot enter from above.
- Where the soil is salty, ask the engineer which cement and concrete suit salts before pouring.
A simple test before you call for an inspection
Before assuming the tank leaks, rule out the simpler causes:
- Close the supply valve at the meter and leave the tank unused (do not run the pump).
- Mark the water level inside the tank and note the time.
- After several hours or overnight, compare the level. A drop with no use points to a leak in the tank or its connected pipes.
- If the meter turns while the tank is full and all taps are closed, check the float valve; a faulty float causes constant overflow and a high bill without any wall leak.
- Photograph the results and send them with your request; it shortens the inspection.
Tiling a pool after waterproofing
A pool's finish is part of the leak-proofing system, not just its look. Tile or mosaic does not stop water on its own; the protection comes from the waterproofing layer underneath. So tiles go on only after the fill test passes, with an adhesive rated for permanent immersion, a water- and chemical-resistant grout (epoxy is common in pools) and movement joints where the engineer specifies. In an Eastern Province summer, do not leave the waterproofing or adhesive exposed to direct sun for long before covering and filling.
Can you drain a pool completely for repairs?
Do not drain a pool completely without asking an engineer, especially if groundwater is close on your plot. An empty pool can be pushed by the water beneath it, and exposed surfaces in strong sun can crack or lose tiles. Plan draining, repair and refilling within a short period, ideally in the cooler months.
Ask for an inspection
Send photos and the size of the pool or tank on WhatsApp, and we will arrange an inspection and propose a system.
Related services: Waterproofing & Insulation, Tiles, Marble & Granite, Landscaping & Canopies
This service in your city: Dammam, Al Khobar, Dhahran, Qatif, Jubail, Al Ahsa (Hofuf)
Frequently asked questions
How long is the fill test after waterproofing a tank or pool?
The tank or pool is filled and the level watched for several days before finishing or use; the engineer and the product specification set the period. The key is not to tile or backfill before the test passes.
Can roof waterproofing be used in a drinking-water tank?
No. The material inside a drinking-water tank must be suitable for contact with drinking water and for permanent immersion, and the tank is washed and disinfected before use. Ask for the product name and data sheet before you agree.
My water bill is high. Is the tank leaking?
Not necessarily. Close every tap and watch the meter; if it turns while the tank is full, the float valve may be faulty. If the tank level drops with the supply closed and no use, the leak is most likely in the tank or its pipes.
Can a tank be waterproofed without breaking anything?
Often yes: an existing tank is emptied, cleaned, its cracks repaired and treated from the inside, with no digging around it. If the damage is in pipes outside the tank, part of them may need exposing; the inspection decides.